Stepper Motors

Sort By:  
R151  Inc Tax
R173  Inc Tax
RAMPS 1.4 , Mega2560 + A4988 , 2004LCD Controller 3D Printer Kit (Mega )
The Ramps, Arduino Mega and driver board combos are the perfect solution for a mulitaxis system like a 3D printer.

Includes:
1x 3D Printer Controller RAMPS
1x Arduin0-Compatible Mega 2560 R3
5x A4988 StepStick Compatible Stepper Motor Driver Module

MicrocontrollerATmega1280
Operating Voltage5V
Input Voltage (recommended)7-12V
Input Voltage (limits)6-20V
Digital I/O Pins54 (of which 15 provide PWM output)
Analog Input Pins16
DC Current per I/O Pin40 mA
DC Current for 3.3V Pin50 mA
Flash Memory128 KB of which 4 KB used by bootloader
SRAM8 KB
EEPROM4 KB
Clock Speed16 MHz
R651  Inc Tax
2H Microstep driver DM860H
 Drive dimensions are: 117 * 78 * 34mm
The mounting hole distance is 111mm.
Maximum current: 7.2A, resolution: 0.1A
Subdivision range: 400~25600ppr
Impulse response frequency: 200KHz
DC power supply 
The input voltage range: 24~80VDC or AC both OK;
Power supply is greater than 200W. Recommend 48VDC or 48V AC
- Operating Temperature: -10℃~45℃ 
R965  Inc Tax
Arcus NEMA 23 STM-23-3-3 with rear output shaft

Features:

  • 2-Phase Bi-polar Stepper
  • Integrated Connector
  • NEMA 23
  • Double Shaft For Encoder
R1,500
Arduino Uno and CNC sheild kit (Mega )
CNC Shield Board:

Version: 3.0
Color: Red
Size(L*W*H): 68 x 53 x 18 mm
Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)

Features:

1. Uses removable DRV8825 compatible stepper drivers.
2. The extension board can be used for carving machine, 3 d printer driver expansion board
3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino-UNO that turns G-code commands into stepper signals)
4. PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
6. Please note that this is an unassembled kit and Basic soldering skills are needed.

A4988 Stepper Motor Driver:

Color: Red
Size(L*W*H): 20 x 15 x 10 mm
Thermal shutdown circuitry: Yes
Crossover-current protection: Yes
Ground fault protection: Yes
Load short-circuit protection: Yes
Compatible logic supply: 3.3V and 5 V
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16

Uno R3 Board:

MCU: ATmega328
Clock speed: 16 MHz
USB interface: ATmega16U2
Operating voltage: 5 V
I-I / O pin output current: 40 mA max
3.3 V output current: 150 mA max
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
EEPROM: 1 kB
Static RAM (SRAM): 2 kB
Flash memory: 32 kB
Size(L*W*H): 68 x 53 x 10 mm


Package included:

1 x Uno
-R3 Board
1 x CNC Shield Board
4 x DRV8825 Stepper Motor Driver
4 x Heat Sink
1 x USB Cable
1 x 40-Pin Row Needles
R357  Inc Tax
Ballscrew Carrage and Integrated NEMA 23 Motor (Shop Soiled, make an offer)
Specifications
Materials:Aluminum alloy
Effective Travel: 300mm
Overall Size: 460mm*110mm
Slide Width: 90mm*45mm
The Number Of Sliders: 1
Accuracy: 0.01mm
Round Trip Accuracy: 0.05-0.08mm
Ambient Temperature: -10℃-50℃
Quantity: 1pc
R4,025  Inc Tax
Cool Muscle Motors NEMA 17 Stepper motor CM1-C-17L30C

Description - High Performance Closed Loop motor systems

Integrated Motion Modules
The Cool Muscle line of servo motors provide all the common components required for motion control embedded into the motor itself. The seamless integration of both software and hardware components creates highly efficient motion modules that can be easily integrated into existing designs, or used to shorten the development cycle of your new machine.
The Cool Muscle outperforms traditional servo and stepper systems by virtue of the controller's multiple closed feed- back loops with the driver and high resolution encoder. Short wire lengths reduce susceptibility to EMI and noise, while removing servo and encoder cables that often add considerable cost, inventory, and complexity. On-board PLC functionality also reduces machine component count and costs, and allows for modern, elegant machine design. A variety of industrial buses are available for communications and networking with third party host controllers.

Contact for Data Sheet or visit http://www.myostat.ca/coolmuscle for more details

R6,210  Inc Tax
Cool Muscle Motors NEMA 23 Stepper motor CM1-C-23L20C

Description - High Performance Closed Loop motor systems

Integrated Motion Modules
The Cool Muscle line of servo motors provide all the common components required for motion control embedded into the motor itself. The seamless integration of both software and hardware components creates highly efficient motion modules that can be easily integrated into existing designs, or used to shorten the development cycle of your new machine.
The Cool Muscle outperforms traditional servo and stepper systems by virtue of the controller's multiple closed feed- back loops with the driver and high resolution encoder. Short wire lengths reduce susceptibility to EMI and noise, while removing servo and encoder cables that often add considerable cost, inventory, and complexity. On-board PLC functionality also reduces machine component count and costs, and allows for modern, elegant machine design. A variety of industrial buses are available for communications and networking with third party host controllers.

Contact for Data Sheet or visit http://www.myostat.ca/coolmuscle for more details

R6,210  Inc Tax
Cool Muscle Motors The Y programming cable - serial or USB

Description - High Performance Closed Loop motor systems

Integrated Motion Modules
The Cool Muscle line of servo motors provide all the common components required for motion control embedded into the motor itself. The seamless integration of both software and hardware components creates highly efficient motion modules that can be easily integrated into existing designs, or used to shorten the development cycle of your new machine.
The Cool Muscle outperforms traditional servo and stepper systems by virtue of the controller's multiple closed feed- back loops with the driver and high resolution encoder. Short wire lengths reduce susceptibility to EMI and noise, while removing servo and encoder cables that often add considerable cost, inventory, and complexity. On-board PLC functionality also reduces machine component count and costs, and allows for modern, elegant machine design. A variety of industrial buses are available for communications and networking with third party host controllers.

Contact for Data Sheet or visit http://www.myostat.ca/coolmuscle for more details

R920  Inc Tax
Flexible Shaft Coupling CNC Stepper Motor Coupler.
Flexible Coupling suitable for stepper motor to leadscrew conversion.

Options of ID vary, 
Please confirm stock
5mm to 5 mm
6 mm to 8mm
5mm to 8 mm 
8mm to 10mm 



OD 18mmx25mm
R35  Inc Tax
H-Bridge Dual Stepper Motor Controller
Onboard two the L9110S motor control chip
simultaneously drive two DC motors or a 4-wire 2-phase stepper motor
input voltage :2.5-12V
800mA continuous current output capability per channel

1. Low static work current

2. Power supply voltage: DC2.5-12V

3. Each channel has 800mA continuous current output

4. Low saturation pressure drop

5. TTL/CMOS output level compatible, can be connected directly to the CPU

6. Output built-in clamping diode, apply to the perceptual load

7. Control and drive integrate in IC

8. Pin high pressure protection function

9. Working temperature: 0-80 ℃
10.Size:29.2(mm)x23(mm)
R31  Inc Tax
H-Bridge Stepper Motor Controller L298N for Arduino
The L298 is an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the con

1. Low static work current

2. Power supply voltage: DC5-36V

3. Each channel has 2500mA continuous current output

4. Low saturation pressure drop

5. TTL/CMOS output level compatible, can be connected directly to the CPU

6. Output built-in clamping diode, apply to the perceptual load

7. Control and drive integrate in IC
R52  Inc Tax
L293D 4 Channel Motor Driver
Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO Description:L293D is a monolithic integrated, high voltage, high current, 4-channel driver.
L293D is a monolithic integrated, high voltage, high current, 4-channel driver,you can use DC motors and power supplies of up to 36 Volts, the L293D chip is also known as a type of H-Bridge,which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.
  •     2 interface for 5V Servo connected to the Arduino’s high-resolution dedicated timer – no jitter.
  •     Can drive 4 DC motors or 2 stepper motors or 2 Servo.
  •     Up to 4 bi-directional DC motors with individual 8-bit speed selection.
  •     Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
  •     4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC.
  •     Pull down resistors keep motors disabled during power-up.
  •     2 external terminal power interface, for seperate logic/motor supplies.
  •     Tested compatible for Arduino Mega, Diecimila & Duemilanove.
  •     Reset button.
Feature:
  • Control up to 4 DC motors.
  • Control 2 Servos.
  • Logic Control Voltage VSS: 4.5 ~ 5.5 V
  • Motor Supply Voltage VSS: 15v
  • Drive operating current IO: 1.2A
  • 8 Stage Serial Shift Registers

R69  Inc Tax
L298P Dual Channel Motor Driver & acc board

The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features.

Operating Voltage 5V to 12V
Motor controller   L298P, Drives 2 DC motors or 1 stepper motor
Max current  2A per channel or 4A max (with external power supply)
Current sensing    1.65V/A
Free running stop and brake function
R115  Inc Tax
LAM Technologies M1233070S8 (3.0Nm 4.2A) with 8 mm output shaft (M1233070S8 (3.0Nm 4.2A))
Nema 23 Stepper motor, for datasheet see the link

https://drive.google.com/open?id=1HzxXtK54l1XoSfb23uATHW3CB-Bsubpr


R1,232  Inc Tax
LAM Technologies M1343020 (4.4Nm 5.6A) (M1343020 (4.4Nm 5.6A))
Nema 34 Stepper motor, for datasheet see the link

https://drive.google.com/open?id=1iOHjTJKXqHPvYOa_6fxh-g3mlMABgek0


R2,067  Inc Tax
LAM Technologies M1343021 (4.4Nm 7.1A) (M1343021 (4.4Nm 7.1A) )
Nema 34 Stepper motor, for datasheet see the link

https://drive.google.com/open?id=1iOHjTJKXqHPvYOa_6fxh-g3mlMABgek0


R2,067  Inc Tax
LAM Technologies M1343050 (9.2Nm 7.1A) (M1343050 (9.2Nm 7.1A) )
Nema 34 Stepper motor, for datasheet see the link

https://drive.google.com/open?id=1iOHjTJKXqHPvYOa_6fxh-g3mlMABgek0


R2,901  Inc Tax
LAM Technologies M1343051 (9.2Nm 10.0A) (M1343051 (9.2Nm 10.0A) )
Nema 34 Stepper motor, for datasheet see the link

https://drive.google.com/open?id=1iOHjTJKXqHPvYOa_6fxh-g3mlMABgek0


R2,901  Inc Tax
LAM Technologies Nema 17 M1173041 (0.50Nm 1.7A) (M1173041 (0.50Nm 1.7A) )
Nema 17 Stepper motor, for datasheet see the link

https://drive.google.com/open?id=1DipBb-lQ1mryMuCyzLrcDceXKDX4CGhb


R569  Inc Tax
LAM Technologies Nema 23 M1233041S8 (1.1Nm 4.2A) with 8 mm output shaft (M1233041S8 (1.1Nm 4.2A))
Nema 23 Stepper motor, for datasheet see the link

https://drive.google.com/open?id=1HzxXtK54l1XoSfb23uATHW3CB-Bsubpr


R705  Inc Tax
LAM Technologies Nema 23 M1233062S8 (1.8Nm 4.2A) with 8 mm output shaft (M1233041S8 (1.8Nm 4.2A))
Nema 23 Stepper motor, for datasheet see the link

https://drive.google.com/open?id=1HzxXtK54l1XoSfb23uATHW3CB-Bsubpr


R923  Inc Tax
LAM Technologies Programmable Stepper Motor driver DS30 Series DS3044 (50Vdc 4Arms 5.6Apk) (DS3044)
This is a high quality stepper motor driver unit from LAM Technologies.

These rugged units are DIN Rail mountable. 

See series Broucher link: 
https://drive.google.com/open?id=1j9_EtHJR1baWrxCmBTUk2R3RNR1pk45D

If you require a datasheet please email Peter at peter@hornet.cc
R3,256  Inc Tax
LAM Technologies Stepper Motor driver DS10 Series DS1078 (90Vdc 10Arms 14.1Apk) (1078)
This is a high quality stepper motor driver unit from LAM Technologies.

These rugged units are DIN Rail mountable. 

See series Broucher link: 
https://drive.google.com/open?id=1j9_EtHJR1baWrxCmBTUk2R3RNR1pk45D

If you require a datasheet please email Peter at peter@hornet.cc
R3,725  Inc Tax
LAM Technologies Stepper Motor driver DS1044 (50Vdc 4Arms 5.6Apk) (1044)
This is a high quality stepper motor driver unit from LAM Technologies.

These rugged units are DIN Rail mountable. 

See series Broucher link: 
https://drive.google.com/open?id=1j9_EtHJR1baWrxCmBTUk2R3RNR1pk45D

If you require a datasheet please email Peter at peter@hornet.cc
R2,192  Inc Tax
LAM Technologies Stepper Motor driver DS5444 (50Vdc 4Arms 5.6Apk) (1044)
This is a high quality stepper motor driver unit from LAM Technologies.

These rugged units are DIN Rail mountable. 

See series Broucher link: 
https://drive.google.com/open?id=1wssemjv6nZ-nXOebrgbSYh6CbhQOmbIx

If you require a datasheet please email Peter at peter@hornet.cc
R3,881  Inc Tax
LAM Technologies Stepper Motor driver DS5448 (50Vdc 8Arms 11.3Apk) (DS5448)
This is a high quality stepper motor driver unit from LAM Technologies.

These rugged units are DIN Rail mountable. 

See series Broucher link: 
https://drive.google.com/open?id=1wssemjv6nZ-nXOebrgbSYh6CbhQOmbIx

If you require a datasheet please email Peter at peter@hornet.cc
R4,778  Inc Tax
LAM Technologies Stepper Motor driver DS5478 (90Vdc 10Arms 14.1Apk) (DS5478)
This is a high quality stepper motor driver unit from LAM Technologies.

These rugged units are DIN Rail mountable. 

See series Broucher link: 
https://drive.google.com/open?id=1wssemjv6nZ-nXOebrgbSYh6CbhQOmbIx

If you require a datasheet please email Peter at peter@hornet.cc
R5,634  Inc Tax
Leadscrew 300 mm

Stainless steel leadscrew

Brass Nut

Length : 300 mm

R151  Inc Tax
Leadscrew 500 mm

Stainless steel leadscrew

Brass Nut

Length : 500 mm

R173  Inc Tax
Leadscrew 500 mm with brass nut Coupling bearings and Stepper Motor kit

Stainless steel leadscrew

Brass Nut

Length : 500 mm

R345  Inc Tax
Linear rail 380mm diameter 8mm

Stainless steel precision ground rod

fits with the LM8UU and polymer equivalent. 

Length : 380 mm

R104  Inc Tax
Linear rail 400 mm diameter 8mm

Stainless steel precision ground rod

fits with the LM8UU and polymer equivalent. 

Length : 400 mm

R77  Inc Tax
Linear rail 400 mm diameter 8mm

Stainless steel precision ground rod

fits with the LM8UU and polymer equivalent. 

Length : 400 mm

R77  Inc Tax
Linear rail 440 mm diameter 8mm

Stainless steel precision ground rod

fits with the LM8UU and polymer equivalent. 

Length : 440 mm

 

R120  Inc Tax
Linear rail 480 mm diameter 8mm

Stainless steel precision ground rod

fits with the LM8UU and polymer equivalent. 

Length : 480mm

R131  Inc Tax
Linear rail 500 mm diameter 8mm (20)

Stainless steel precision ground rod

fits with the LM8UU and polymer equivalent. 

Length : 500 mm

R137  Inc Tax
Master network card CM1DC1-MBSC

Description - High Performance Closed Loop motor systems

Integrated Motion Modules
The Cool Muscle line of servo motors provide all the common components required for motion control embedded into the motor itself. The seamless integration of both software and hardware components creates highly efficient motion modules that can be easily integrated into existing designs, or used to shorten the development cycle of your new machine.
The Cool Muscle outperforms traditional servo and stepper systems by virtue of the controller's multiple closed feed- back loops with the driver and high resolution encoder. Short wire lengths reduce susceptibility to EMI and noise, while removing servo and encoder cables that often add considerable cost, inventory, and complexity. On-board PLC functionality also reduces machine component count and costs, and allows for modern, elegant machine design. A variety of industrial buses are available for communications and networking with third party host controllers.

Contact for Data Sheet or visit http://www.myostat.ca/coolmuscle for more details

R1,845  Inc Tax
Per Page      1 - 40 of 77