Servo Motors

Sort By:  
MG90S Horns set (MG90S Horns set)
  • Servo horn Set for MG90S
PWM expansion board I2C PCA9685
This module is ideally suited to adding PWM control to your project, whether it be driving an LED array or an array of servo motors, this module will drive arrays for days. Based on the PCA9685 chipset which features its own internal clock the module allows for the control of 16 seperate PWM channels through a 2 - wire connection.
The module requires an external power supply of 5V to be able to drive the connected devices. The logic of the board itself is powered through the host microcontroller. Communication is handled through a 2 pin I2C interface, available on a wide range of microcontrollers. The I2C address of the module is in the range of 0x60 - 0x80 depending on the configuration of the onboard address select pins.
Please do not hesitate to contact us if you require further information regarding the module's operation.
PinDescription
GND0V
OEOutput enable
SCLI2C Clock
SDAI2C Data
VCC5V Input
V+Screw terminal voltage
9g Servo motor (9g)
Specs:
  • Weight : 9g
  • Size : 22mm x 11.5mm x 27 mm
  • Operating Speed (4.8V no load): 0.12sec/60 degrees
  • Torque (4.8V): 17.5oz/in (1.2 kg/cm)
  • Temperature Range: -30 to +60 Degree
  • Dead Band Width: 7usec
  • Operating Voltage:3.0-7.2 Volts
  • All Nylon Gear
  • Connector Wire Length Approx. 250MM(10in)
  • Package: 10 pcs
  • 100% Genuine.
  • Includes servo arms.
20g Servo motor MG996R (MG 996R)
Specs:
  • lifting Weight : 20g
  • Size : 20mm x 40 mm x 39.5 mm
  • Operating Speed (4.8V no load): 0.12sec/60 degrees
  • Torque approximately (4.8V): (150 kg/cm)
  • Temperature Range: -30 to +60 Degree
  • Dead Band Width: 7usec
  • Operating Voltage:3.0-7.2 Volts
  • All Nylon Gear
  • Connector Wire Length Approx. 250MM
  • Includes servo arms.
Ask Peter about data sheets at peter@hornet.cc

Also ask if needing a free running option.

For Datasheet see link
https://drive.google.com/open?id=1H7ky3cAcQpTGmnILeJ_gU2jXxRKakuGc
11kg/cm Servo motor MG995 (MG 996R)

MG995

Specification:

Weight: 55g
Dimension: 40.7×19.7×42.9mm
Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6v)
Operating speed: 0.20sec/60degree (4.8v); 0.16sec/60degree (6.0v)
Operating voltage: 4.8~ 6.6v
Gear Type: Metal gear
Temperature range: 0- 55deg
Dead band width: 1us
servo wire length: 32cm
Current draw at idle 10MA
No load operating current draw 170MA
Stall current draw 1200MA
Servo Plug: JR (Fits JR and Futaba)
servo arms &screws included and fit with Futaba servo arm
It’s universal “S” type connector that fits most receivers, including Futaba, JR, Hitec ,GWS, Cirrus, Blue Bird, Blue Arrow, Corona, Berg, Spektrum.
CE &RoHS approved
We have upgraded our servo gear set and shaft to aluminum 6061-T6.
It is stronger and lighter than copper.

MG90S Metal gear servo (9g)
Specs:
  • Weight : 9g
  • Size : 22mm x 11.5mm x 27 mm
  • Operating Speed (4.8V no load): 0.12sec/60 degrees
  • Torque (4.8V): 17.5oz/in (1.2 kg/cm)
  • Temperature Range: -30 to +60 Degree
  • Dead Band Width: 7usec
  • Operating Voltage:3.0-7.2 Volts
  • All Nylon Gear
  • Connector Wire Length Approx. 250MM(10in)
  • Package: 10 pcs
  • 100% Genuine.
  • Includes servo arms.
FS5103R Continuous Servo Motor (FS5103R )
  • FS5103R Continuous Servo Motor
  • Operating Speed: 0.18sec / 60degree (4.8V), 0.16sec / 60degree (6V)
  • Stall Torque: 3kg.cm / 41.74oz.in(4.8V), 3.2kg.cm / 44.52oz.in(6V)
  • Operating Voltage: 4.8V~6V
  • Control System: Analog / Direction: CCW
  • Operating Angle: 360degree / Required Pulse: 500us-2500us
20g Servo motor PDI 6221MG (MG 996R)
Specs:
  • lifting Weight : 20g
  • Size : 20mm x 40 mm x 39.5 mm
  • Operating Speed (4.8V no load): 0.12sec/60 degrees
  • Torque approximately (4.8V): (150 kg/cm)
  • Temperature Range: -30 to +60 Degree
  • Dead Band Width: 7usec
  • Operating Voltage:3.0-7.2 Volts
  • All Nylon Gear
  • Connector Wire Length Approx. 250MM
  • Includes servo arms.
Ask Peter about data sheets at peter@hornet.cc

Also ask if needing a free running option.

For Datasheet see link
https://drive.google.com/open?id=1H7ky3cAcQpTGmnILeJ_gU2jXxRKakuGc
PWM Servo Sheild -B
Looking to build an Arduino based robot? Drive a ton of LEDs with a very precise PWM output? The Arduino Uno only has a limited number of PWM pins – this shield adds an additional 16 PWM channels, each with 12 Bit resolution! Since this board communicates using I2C, up to 62 of these boards can be used on the same Arduino. That means you can control up to 992 PWM outputs!
  • Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs
  • It's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
  • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
  • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
  • Adjustable frequency PWM up to about 1.6 KHz
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
  • Configurable push-pull or open-drain output
  • Output enable pin to quickly disable all the outputs
  • Terminal block for power input (or you can use the 0.1" breakouts on the side)
  • Reverse polarity protection on the terminal block input
  • Green power-good LED
  • 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
  • "Chain-able" design
  • A spot to place a big capacitor on the V+ line (in case you need it)
  • 330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
  • Solder jumpers for the 6 address select pins
Actuonix Linear Acutuator Controller LAC (LAC)

Linear Actuator Control Board


You can purchase an LAC board for half price, just $20 when purchased with a P-Series feedback actuator.

The Linear Actuator Control Board is a stand-alone, closed-loop control board specifically designed for Actuonix P-series micro linear actuators. The LAC simplifies designs by saving the development time, cost and processor overhead associated with direct motor control. As little as 1 digital or analog output is required for position control. Supported input signals include USB, voltage, current, RC servo and PWM. On-board adjustment of speed, sensitivity and stroke limits are available. 

This linear actuator controller can be operated as both an interface board or as a stand alone controller with the addition of an external potentiometer and power supply. Each LAC board controls 1 linear actuator and will require an external power supply rated for the actuator.

The LAC is compatible with all P-series micro linear actuator on this site. A 6 volt or 12 volt power supply is required for operation.

Please note: the LAC board is only compatible with P-series actuators. It will not work with S, I or R actuators.

Download the LAC datasheet here 
Download the LAC Servo Actuator Quick Start Guide. This is for using our LAC with the larger feedback actuators via RC.
Download the LAC USB Control & Configuration guide here.
Download the LAC Software
.
Add to Cart
R1,357
Actuonix Linear actuator Model P16-200-256-12-P Servo Motor (P16-200-256-12-P)
Contact Peter at peter@hornet.cc if in need of a data sheet
Add to Cart
R1,742
Per Page      1 - 14 of 14
  • 1