Arduino

Sort By:  
Ultrasonic sensor Bracket (HC-SR04)

Overview

This bracket is for the HC-SR04 sensor
http://stelltron.co.za/index.php?rt=product/product&path=74&product_id=133
MCP9700A-E/TO 9700 Low-Power Linear Active Thermistor Sensor Microchip
Linear Active Thermistor™ ICs are sensors whose output voltage is directly proportional to measured temperature. The MCP9700 can accurately measure temperature from -40C to +150C. The output of the MCP9700 is calibrated to a slope of 10mV/°C and has a DC offset of 500mV. The offset allows reading negative temperatures without the need for a negative supply. The MCP9700 is packaged in space saving 5-pin SC-70 packages, making it ideal for space-critical and low-cost applications.
Infrared Obstacle Avoidance Sensor Module for Arduino Smart Car Robot 3-wire
  • Module description :
  •     The sensor module light is adaptable to the environment, it has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving tube, after the comparator circuit processing, green indicator will light up, at the same time signal output interface to output digital signal (a low level signal), can be through the potentiometer knob adjust the detection distance, effective distance range 2 ~ 30cm, working voltage is 3.3V to 5V. The sensor detection range can be through the potentiometer to adjust and have small interference, easy to assemble, easy to use, etc, can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on many occasions.
  •  
  • Module parameters:
  • 1. when the module detects obstacles in front of the signal, the green indicator on the circuit board light level and at the same time the OUT port output low level signal, the detection module from 2 ~ 30cm, 35°detection Angle, test distance can be adjusted through the potentiometer, adjustable potentiometer clockwise, the detection distance increases; Counter-clockwise tuning potentiometer, detection distance is reduced.
  • 2. sensors, active infrared reflection detection, therefore the reflectivity and shape of the target is the key of the detection range. White one black detection range, minimum maximum; Small area of the object distance, large distance.
  • 3. the sensor module output port OUT can be directly connected to the microcontroller IO port can, also can drive a 5v relay directly; Connection mode: the VCC - VCC; GND - GND; The OUT - the IO
  • 4. the comparator USES the LM393, working stability;
  • 5. can be used for 3 to 5v dc power to power supply module. When power on, the red power indicator light lit;
  • 6. 3 mm screw holes, easy fixed, installation;
  • 7. circuit board size: 3.2CM*1.4CM
  • 8. each module is shipped already compare threshold voltage through the potentiometer to adjust good, not special circumstances, please do not arbitrarily adjust the potentiometer.
  •  
  • Module interface specification 
  • 1. VCC voltage is 3.3V to 5V converter (which can be directly connected to 5V single-chip microcontroller and 3.3V) 
  • 2. GND external GND 
  • 3. OUT of small plate digital output interface (0 and 1)
I2C character LCD backpack LCD1602 / LCD2004

By using simple i2c input/output expanders we have reduced the number of pins (only 2 pins are needed for i2c) while still making it easy to interface with the LCD. forarduino users, we provide a easy-to-use library that is backwards compatible with projects using the '6 pin' wiring. 

This backpack will work with any 'standard' character LCD, from 8x1 to 20x4 sizes! As long as they have a 16-pin single-line connection header at the top. We carry a few LCDs that work great. We suggest using our blue & white 20x4 or 16x2 LCDs. It does not work with the 16x2 OLED displays.

Attiny Development Board (5V adjustable 16M MEGA328)
Make your Arduino projects tiny with the ATtiny series development boards
Real Time Clock (DS1307)

DS1307 Real Time Clock

SPECIFICATION

- Color: Blue
- Quantity: 1
- Material: Circuit board
- Memory storage: 24C32 32K I2C EEPROM
- With LIR2032 rechargeable lithium battery and rechargeable circuit
- With reading and writing function
- Using time: About 1 year (Fully charged)
- Provide clock signal for microcontroller
- Cascade other I2C devices
- With full BCD clock calendar chip of 56byte non-volatile RAM
- Address and data transmission via serial cable with dual-line dual-direction
- The chip can provide second, minute, hour etc information.
- AM/PM mark, for working 24-hour or 12-hour
- Built-in power sensor circuit in the chip, with brownout detection and battery switch function
- Under battery backup mode, power consumption is below 500uA
- Accurate calendar up to year 2100
- Great for DIY project

H-Bridge Dual Stepper Motor Controller
Onboard two the L9110S motor control chip
simultaneously drive two DC motors or a 4-wire 2-phase stepper motor
input voltage :2.5-12V
800mA continuous current output capability per channel

1. Low static work current

2. Power supply voltage: DC2.5-12V

3. Each channel has 800mA continuous current output

4. Low saturation pressure drop

5. TTL/CMOS output level compatible, can be connected directly to the CPU

6. Output built-in clamping diode, apply to the perceptual load

7. Control and drive integrate in IC

8. Pin high pressure protection function

9. Working temperature: 0-80 ℃
10.Size:29.2(mm)x23(mm)
Rain Weather Module Raindrops Detection Sensor Moduel Humidity For Arduino
Specification:
Product use: rain, rain sensor, can be used for all kinds of weather monitoring, and translated into output signals and AO.
The sensor USES the high quality FR - 04 double material, large area of 5.5 * 4.0 CM, treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance;
The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 mA;
With potentiometer sensitivity adjustment
The working voltage of 3.3 V to 5 V
The output format: digital switch output (0 and 1) and analog AO voltage output;
Has a fixed bolt hole, convenient installation
Small board PCB size: Approx. 3.2 cm x 1.5 cm
The LM393, use of wide voltage comparator

Package Included:

1X Humidity Detection Sensor Module Snow Rain raindrops Detection For Arduino
Soil Hygrometer Humidity Detection Module Soil Moisture Water Sensor
This is a simple water sensor, which can be used to detect soil moistureDual output mode, analog output is accurateA fixed bolt hole for easy installationWith power indicator (red) and digital switching output indicator (green)LM393 comparator chip, stableSpecifications:VCC: 3.3V-5VGND: GNDDO: digital output interface(0 and 1)AO: analog output interfacePanel PCB Dimension: 3 x 1.5 cmSoil Probe Dimension: 6 x 2 cmWire length: 21 cmNet weight:11 gPackage weight:21 gColor: Random DeliveryPackage Content:1 x Soil Moisture Detector Module 1 x Probe 5 x Jumper Cables
Microphone Sensor AVR PIC High Sensitivity Sound Detection Module

 

Microphone Sensor AVR PIC High Sensitivity Sound Detection Module For Arduino

 

 

Product Description
Features:

  100% Brand new and high quality
  For sound detection module has two outputs:
  1. AO, analog output, real-time output voltage signal of the microphone
  2. DO, when the sound intensity reaches a certain threshold, the output high and low signal
  
  
  Module features:
  1. There is a mounting screw hole 3mm
  2. The use 5v DC power supply
  3. With analog output
  4. There are threshold level output flip
  5. High sensitive microphone and high sensitivity.
  6. A power indicator light
  7. The comparator output is light

GY-2561 TSL2561 Luminosity Sensor Breakout Infrared Light Sensor
Digital light intensity detecting.
The ROHM genuine BH1750FVI chip.
Power supply :3-5v.
Data range :0-65535.
The sensor built 16bitAD converter.
Direct digital output, complex calculation is omitted, omitting calibration.
Does not distinguish between ambient light.
Close to the visual sensitivity of the spectral characteristics.
1 lux high-precision measurement of a wide range of brightness.
ATtiny85 (5V adjustable 16M MEGA328)
Make your Arduino projects tiny with the ATtiny series
For an idea of how the attiny works have a look at https://www.youtube.com/watch?v=9LjfkjwMqXI

For datasheet, follow this link https://drive.google.com/open?id=1FeX4ffKtFMynuZ4Pq7E1Mb7K63F31ywh

We also carry the development boards http://stelltron.co.za/index.php?rt=product/product&path=71_77&product_id=490
Tilt Sensor Module Vibration Sensor for Arduino STM32 AVR Raspberry Pi
Tilt Angle Module Vibration Sensor Module for Arduino STM32 AVR
PCB board size: 16*14mm
location hole diam: 3.1mm
with Free cable
Working Voltage: 3.3-12V
BH1750FVI Digital Light intensity Sensor Module For AVR Arduino 3V-5V power
Digital light intensity detecting.
The ROHM genuine BH1750FVI chip.
Power supply :3-5v.
Data range :0-65535.
The sensor built 16bitAD converter.
Direct digital output, complex calculation is omitted, omitting calibration.
Does not distinguish between ambient light.
Close to the visual sensitivity of the spectral characteristics.
1 lux high-precision measurement of a wide range of brightness.
4x3 Matrix 12 Key Array Membrane Switch Keypad For Arduino
4 x 3 Matrix 12 Key Array Membrane Switch Keypad Keyboard For Arduino

Description:

Pad Size: 68.9 x 76 x 0.8mm
Cable length: 85mm (include connector)
Connector: dupont 7 pins, 0.1 inch (2.54mm) Pitch
Mount style: Self-Adherence
Max. circuit rating: 35VDC, 100mA
Insulation spec.: 100M Ohm, 100V
Dielectric withstand: 250Vrms (60Hz, 1min)
Contact bounce: ≤5ms
Life expectancy: 1 million closures
Weight: 7g

Package included:

3 x Membrane switch Matrix Array 12 key
Ultrasonic Ranging Sensor (HC-SR04)

Overview

This HC-SR04 has stable performance and high ranging accuracy.

Specifications

  • Power Supply : 5V DC
  • Effectual Angle : < 30 degrees
  • Ranging Distance : 2cm to 500 cm
  • Resolution : 1cm
  • Ultrasonic Frequency : 40kHz
BMP280 Pressure Sensor Module High Precision (BMP280)

Bosch has stepped up their game with their new BMP280 sensor, an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI!
    This precision sensor from Bosch is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuracy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with ±1 meter accuracy
Enhancement of GPS navigation

    e.g.time-to-first-fix improvement,dead-reckoning,slope detection
    Indoor navigation(floor detection,elevator detection)
    Outdoor navigation,leisure and sports applications
    Weather forecast
    Health care application(e.g. sirometry)
    Vertical velocity indication(e.g. risk/sink speed)
    Target devices
    Handsets such as mobile phones ,table PCs,GPS devices
    Navigation systems
    Portable health caredevices
    Home weather stations
    Flying toys
    Watches
    PCB size:(L*W)1.52* 1.20cm/0.60"*0.47"

HC-SR501 IR motion sensor (HC-SR501)

HC-SR501 IR motion sensor

You can use this 3-pin PIR sensor to detect people and animals from up to 20 feet away. It has configurable timing and can be enabled for single or repeat signaling.

SPECIFICATIONS

  • Voltage: 5V – 20V

  • Power Consumption: 65mA

  • TTL output: 3.3V, 0V

  • Lock time: 0.2 sec

  • Trigger methods: L – disable repeat trigger, H enable repeat trigger

  • Sensing range: less than 120 degree, within 7 meters

  • Temperature: – 15 ~ +70

  • Dimension: 32*24 mm, distance between screw 28mm, M2, Lens dimension in diameter: 23mm

ATtiny45 (5V adjustable 16M MEGA328)
Make your Arduino projects tiny with the ATtiny series For an idea of how the attiny works have a look at https://www.youtube.com/watch?v=9LjfkjwMqXI For datasheet, follow this link https://drive.google.com/open?id=1FeX4ffKtFMynuZ4Pq7E1Mb7K63F31ywh We also carry the development boards http://stelltron.co.za/index.php?rt=product/product&path=71_77&product_id=490
H-Bridge Stepper Motor Controller L298N for Arduino
The L298 is an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the con

1. Low static work current

2. Power supply voltage: DC5-36V

3. Each channel has 2500mA continuous current output

4. Low saturation pressure drop

5. TTL/CMOS output level compatible, can be connected directly to the CPU

6. Output built-in clamping diode, apply to the perceptual load

7. Control and drive integrate in IC
MPU-6050 Module 3 Axis Gyroscope+Accelerometer Module for Arduino MPU 6050
GY-521 MPU-6050 Module 3 Axis Gyroscope+ 3 Axis Accelerometer Module for Arduino.
MPU-6050 Accelerometer + Gyro
The MPU-6050 sensor contains a MEMS accelerometer and a MEMS gyro in a single chip.
It is very accurate, since it contains 16-bits analog to digital conversion hardware for each channel.
Therefor it captures the x, y, and z channel at the same time.
Name: MPU-6050 module (three-axis gyroscope + triaxial accelerometer)
Use Chip: MPU-6050
Power supply :3-5v (internal low dropout regulator)
Communication: IIC communication protocol standard
16bit AD converter-chip, 16-bit data output
Gyro Range: ¡À 250 500 1000 2000 ¡ã / s
Acceleration range: ¡À 2 ¡À 4 ¡À 8 ¡À 16g
Using Immersion Gold PCB, welding machines to ensure quality
2.54mm pin spacing
Size:2x1.6x0.1mm
Application£º
Motion sensing games
Augmented Reality
Electronic Image Stabilization (EIS: Electronic Image Stabilization)
Optical Image Stabilization (OIS: Optical Image Stabilization)
"Zero-touch" gestures User Interface
Pedestrian navigation
Gesture shortcuts
Market:
Smart phone
Tablet device
Handheld games
3D remote controller
Portable navigation devices
MAG3110 magno 3Axis
Features:

Size: 16mm * 17mm
Integrated 5V to 3.3V chip, more convenient for 5V power supply microcontroller system
I2C compatible 3-5V system


Package included:

1 x Sensor

FT232RL 3.3V 5.5V FTDI USB to TTL Serial Adapter Module for Arduino Mini Port
Specifications:

This programmer is used to flash code onto a Arduino Pro Mini 3.3V/5V


    100% brand new
    Support 3.3V, 5V
    chipset FT232RL
    USB power has over current protection, using 500MA self-restore fuse
    RXD/TXD transceiver communication indicator
    Pin definition: DTR,RXD,TX,VCC,CTS,GND
    Pitch:2.54mm
    Module size:36mm(length)*17.5mm(width)
    Driver download address:
    http://www.ftdichip.com/FTDrivers.htm
Arduino Pro Mini 5V 16MHz ATmega128 (5V adjustable 16M MEGA328)
Dimensions: 0.7x1.3" (18x33mm)

Features:
  • ATmega328 running at 16MHz with external resonator (0.5% tolerance)0.8mm
  • Thin PCBUSB connection off board
  • Supports auto-reset5V regulatorMax 150mA output
  • Over current protected
  • Weighs less than 2 grams!
  • DC input 5V up to 12V
  • On board Power and Status LEDs
  • Analog Pins: 8
  • Digital I/Os: 14
Arduino Pro Mini 3.3V 16MHz (3.3V 8MHz MEGA328P)
Dimensions: 0.7x1.3" (18x33mm)
Features:
  • ATmega328 running at 8MHz with external resonator (0.5% tolerance)
  • Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc)
  • 0.8mm Thin PCB
  • USB connection off board
  • Weighs less than 2 grams!
  • Supports auto-reset3.3V regulatorMax 150mA output
  • Over current protectedDC input 3.3V up to 12V
  • On board Power and Status LEDsAnalog
  • Pins: 8Digital
  • I/Os: 14
L293D 4 Channel Motor Driver
Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO Description:L293D is a monolithic integrated, high voltage, high current, 4-channel driver.
L293D is a monolithic integrated, high voltage, high current, 4-channel driver,you can use DC motors and power supplies of up to 36 Volts, the L293D chip is also known as a type of H-Bridge,which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.
  •     2 interface for 5V Servo connected to the Arduino’s high-resolution dedicated timer – no jitter.
  •     Can drive 4 DC motors or 2 stepper motors or 2 Servo.
  •     Up to 4 bi-directional DC motors with individual 8-bit speed selection.
  •     Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
  •     4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC.
  •     Pull down resistors keep motors disabled during power-up.
  •     2 external terminal power interface, for seperate logic/motor supplies.
  •     Tested compatible for Arduino Mega, Diecimila & Duemilanove.
  •     Reset button.
Feature:
  • Control up to 4 DC motors.
  • Control 2 Servos.
  • Logic Control Voltage VSS: 4.5 ~ 5.5 V
  • Motor Supply Voltage VSS: 15v
  • Drive operating current IO: 1.2A
  • 8 Stage Serial Shift Registers

Arduino Micro (5V adjustable 16M MEGA328)
MicrocontrollerATmega32U4
Operating Voltage5V
Input Voltage (recommended)7-12V
Input Voltage (limit)6-20V
Digital I/O Pins20
PWM Channels7
Analog Input Channels12
DC Current per I/O Pin20 mA
DC Current for 3.3V Pin50 mA
Flash Memory32 KB (ATmega32U4) of which 4 KB used by bootloader
SRAM2.5 KB (ATmega32U4)
EEPROM1 KB (ATmega32U4)
Clock Speed16 MHz
LED_BUILTIN13
Length48 mm
Width18 mm
Weight13 g
ESP8285 WiFi Communication Moduel

Datasheeet Link -> https://drive.google.com/open?id=18iyGjssAjdAkn4zSX1DKlcDgo1s0mX0l
ESP8266 WiFi Communication Moduel development board

ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.

 

ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.

 

Corresponding Interface:

    SDIO 2.0, SPI, UART

    32-pin QFN package

    Integrated RF switch, balun, 24dBm PA, DCXO, and PMU

    Integrated RISC processor, on-chip memory and external memory interfaces

    Integrated MAC/baseband processors

    Quality of Service management

    I2S interface for high fidelity audio applications

    On-chip low-dropout linear regulators for all internal supplies

    Proprietary spurious-free clock generation architecture

    Integrated WEP, TKIP, AES, and WAPI engines

 

Specification:

    802.11 b/g/n

    Wi-Fi Direct (P2P), soft-AP

    Integrated TCP/IP protocol stack

    Integrated TR switch, balun, LNA, power amplifier and matching network

    Integrated PLLs, regulators, DCXO and power management units

    +19.5dBm output power in 802.11b mode

    Power down leakage current of<10uA

    Integrated low power 32-bit CPU could be used as application processor

    SDIO 1.1/2.0, SPI, UART

    STBC, 1×1 MIMO, 2×1 MIMO

    A-MPDU & A-MSDU aggregation & 0.4ms guard interval

    Wake up and transmit packets in < 2ms

    Standby power consumption of < 1.0mW (DTIM3)

Compass GY-273

The HMC5883L is a triple-axis magnetometer compass, which uses I2C for communication.

Compass heading accuracy of 1° to 2°, provided by internal 12-bit ADC (Analog-to-Digital Converter).

Includes on-board voltage regulator, allowing you to power the module with voltages between 3.3V and 6V.

The module includes on-board pull-up resistors on the I2C lines.

There is a data ready pin (pin DRDY) you can use to make your communication with the module more efficient; refer to the datasheet below for details.

Since this module has such great compass heading accuracy, it is great for giving your robot precise navigation abilities.

PRODUCT CONTENTS:
  • 1 — HMC5883L Triple-Axis Magnetometer Compass GY-273 Module
  • 1 — 1x5 pin male header
SPECIFICATIONS:
Supply Voltage VCC3.3 to 6 V
Heading Accuracy1° to 2°
Magnetic Field Range-8 to +8 Gauss
I2C Address0x1E (7-bit address)
Max Data Rate160 Hz
Digital Voltage Level3.3V
Dimensions (excluding pins)
Length18.2mm (0.717")
Width13.3mm (0.524")
Height2.2mm (0.087")
Weight0.95g (0.034oz)
Arduino Nano IO Shield Expansion Board
Features:
  • New Expansion Board Terminal Adapter DIY Kits for Arduino NANO IO Shield V1.0
  • IO Expansion Shield For Arduino Nano is specifically designed to facilitate
  • an easy connection between Expansion Shield For Arduino Nano and many other devices.
  • In essence, it expands for Arduino Nano controller to link those devices in a simple and trouble free manner.
STM32F030 Development board (5V adjustable 16M MEGA328)
For data sheet follow this link https://drive.google.com/open?id=1wg0aDq_Ufyb1A0r9AcNSsXsS7MEbd5R3
Arduino Nano V3.0 ATmega328P 5V 16MHz (V3.0 ATmega328P CH340G 5V 16M Micro-controller board Arduino)
CH340G Replace FT232RL 
Operating Voltage(logic level):5V

8 analog inputs ports:A0 ~ A7 
14 Digital input / output ports:TX,RX,D2 ~ D13 
6 PWM ports:D3, D5, D6, D9, D10, D11 
1 pairs of TTL level serial transceiver ports RX / TX 
Using Atmel Atmega328P-AU MCU 
There is bootloader installed in it 
Support USB download and Power 
Support for external 5V ~ 12V DC power supply 
Support power supply by 9V battery 
Support ISP download 
CH340G Driver Download link : http://www.wch-ic.com/download/list.asp?id=126 OR http://www.5v.ru/ch340g.htm 
IDE of arduino Download link : http://arduino.cc/en/Main/Software
L298P Dual Channel Motor Driver & acc board

The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features.

Operating Voltage 5V to 12V
Motor controller   L298P, Drives 2 DC motors or 1 stepper motor
Max current  2A per channel or 4A max (with external power supply)
Current sensing    1.65V/A
Free running stop and brake function
Per Page      1 - 40 of 51