Sort By:  
433Mhz RF transmitter and receiver link for Arduino

TX Technical Specifications:

Receiver module parameters

1.Product Model: MX-05V
2.Operating voltage: DC5V
3.Quiescent Current: 4mA
4.Receiving frequency: 433.92MHZ
5.Receiver sensitivity:-105DB
6.Size: 30 * 14 * 7mm
7.External antenna: 32CM single core wire, wound into a spiral

Technical parameters of the transmitter head
1.Product Model: MX-FS-03V
2.Launch distance :20-200 meters (different voltage, different results)
3.Operating voltage :3.5-12V
4.Dimensions: 19 * 19mm
5.Operating mode: AM
6.Transfer rate: 4KB / S
7.Transmitting power: 10mW
8.Transmitting frequency: 433M
9.An external antenna: 25cm ordinary multi-core or single-core line
10.Pinout from left → right: (DATA; VCC; GND)

Application environment

Remote control switch, receiver module, motorcycles, automobile anti-theft products, home security products, electric doors, shutter doors, windows, remote control socket, remote control LED, remote audio remote control electric doors, garage door remote control, remote control retractable doors, remote volume gate, pan doors, remote control door opener, door closing device control system, remote control curtains, alarm host, alarm, remote control motorcycle remote control electric cars, remote control MP3.

1.VCC voltage module operating voltage and good power filtering;
2.Great influence on the antenna module reception, preferably connected to the 1/4 wavelength of the antenna, typically 50 ohm single conductor, the length of the antenna 433M of about 17cm;
3.Antenna position has also affected the reception of the module, the installation, the antenna as possible straight away from the shield, high pressure, and interference source; frequency used to receive, decode and oscillation resistor should match with the transmitter.

R46  Inc Tax
Arduino D1 mini (3.3V 8MHz MEGA328P)
Dimensions: 0.7x1.3" (18x33mm)
  • ATmega328 running at 8MHz with external resonator (0.5% tolerance)
  • Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc)
  • 0.8mm Thin PCB
  • USB connection off board
  • Weighs less than 2 grams!
  • Supports auto-reset3.3V regulatorMax 150mA output
  • Over current protectedDC input 3.3V up to 12V
  • On board Power and Status LEDsAnalog
  • Pins: 8Digital
  • I/Os: 14
R115  Inc Tax
DFRobot GPS Module


  • UBX-G7020-KT solution
  • 1Hz(default) ~ 10Hz output
  • 9600bps(default) [support:4800 ,9600 ,19200 ,38400 ,57600 ,115200 ,230400 ,460800,921600] TTL serial interface
  • 5v @ 30mA (support 3.3~5v)
  • 56-Channel receiver
  • Extremely high sensitivity -161dBm
  • Accuracy 2.5m (Autonomous) / <2m[SBAS]
  • Operating temperature: -40°C to 85°C
  • Hot Start : 1s
  • Warm Start : 28s
  • Cold Start : 29s
  • Module Size 28*28*8.6mm (1.10*1.10*0.34")
  • Enclosure Size 37x48x16mm(1.46x1.89x0.63")
  • LED indicator
Pin Definition:
  • White:PPS
  • Red:VCC
  • Blue:TXD
  • Green:RXD
  • Black:GND
  • Yellow:EN


  • GPS Receiver for Arduino(Model) x1
  • Enclosure x1
  • Cable x1
R596  Inc Tax
ESP8266 WiFi Communication Moduel development board

ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.


ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.


Corresponding Interface:

    SDIO 2.0, SPI, UART

    32-pin QFN package

    Integrated RF switch, balun, 24dBm PA, DCXO, and PMU

    Integrated RISC processor, on-chip memory and external memory interfaces

    Integrated MAC/baseband processors

    Quality of Service management

    I2S interface for high fidelity audio applications

    On-chip low-dropout linear regulators for all internal supplies

    Proprietary spurious-free clock generation architecture

    Integrated WEP, TKIP, AES, and WAPI engines



    802.11 b/g/n

    Wi-Fi Direct (P2P), soft-AP

    Integrated TCP/IP protocol stack

    Integrated TR switch, balun, LNA, power amplifier and matching network

    Integrated PLLs, regulators, DCXO and power management units

    +19.5dBm output power in 802.11b mode

    Power down leakage current of<10uA

    Integrated low power 32-bit CPU could be used as application processor

    SDIO 1.1/2.0, SPI, UART

    STBC, 1×1 MIMO, 2×1 MIMO

    A-MPDU & A-MSDU aggregation & 0.4ms guard interval

    Wake up and transmit packets in < 2ms

    Standby power consumption of < 1.0mW (DTIM3)

R76  Inc Tax
ESP8285 WiFi Communication Moduel

Datasheeet Link ->
R76  Inc Tax
Ethernet Shield W5100 For Arduino UNO ATMega 328 1280 MEGA2560 (Shield W5100 )
  • With this Ethernet Shield, your Arduino board can be used to connect to internet.
  • Can be used as server or client.
  • Directly plug puzzle board, no soldering required.
  • Controller: W5100.
  • This is the latest version of the Ethernet Shield.
  • This Arduino Ethernet Shield which is based on the Wiznet W5100 Ethernet Chip gives you an easy way to get your Arduino Online.
  • It is directly supported by Arduino official Ethernet Library.
  • It adds a micro-SD card slot, which can be used to store files for serving over the network.
  • It is compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560) and can be accessed using the SD library.
  • The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP.
  • It supports up to four simultaneous socket connections.
  • Use the Ethernet library to write sketches which connect to the internet using the shield.
  • Fits all version of arduino Main board,2009,UNO, mega 1280, mega 2560.
  • Size:7cm x 5.4cm x 2.4cm - 2.76inch x 2.12inch x 0.94inch.
  • MAC address: 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
R173  Inc Tax
GSM GPRS Shield for Arduino UNO (Shield W5100 )
The GPRS/GSM Shield provides you a way to use the GSM cell phone network to receive data from a remote location,it delivers GSM/GPRS 850/900/1800/1900MHz signals for Audio, SMS and GPRS Service. It is compatible with all boards which have the same form factor (and pinout) as a standard Arduino UNO Board. This GPRS/GSM shield is configured and controlled via its UART using AT commands. The GPRS Shield Also has 6 GPIOs,2 PWMs and 1 ADC(They are all 2V8 logic), which can be controlled by AT commands of the microcontroller.

Furthermore,to make your project more flexible and efficient,there is the option of two different antennas,One is the traditional GPRS antenna,which is more sensitive; the other is an on-board antenna, this antenna is more compact and easy to install, you can put the whole project into a case more easily,with this kind of antenna.


  • Quad-Band 850/ 900/ 1800/ 1900 MHz
  • GPRS multi-slot class 10/8
  • GPRS mobile station class B
  • Compliant to GSM phase 2/2+
  • Class 4 (2 W @850/ 900 MHz)
  • Class 1 (1 W @ 1800/1900MHz)
  • Control via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands)
  • Low power consumption: 1.5mA(sleep mode)
  • Operation temperature: -40°C to +85 °C
  • 2-in-1 headset jack

Package list

  • GPRS Shield PCBA x 1
  • MicroSim Card converter x 1
  • PCB Antenna x 1
R690  Inc Tax
Hc-05 Bluetooth module
Serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc. Specifications: Bluetooth protocal: Bluetooth Specification v2.0+EDR Frequency: 2.4GHz ISM band Modulation: GFSK(Gaussian Frequency Shift Keying) Emission power: =4dBm, Class 2 Sensitivity: =-84dBm at 0.1% BER Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps Security: Authentication and encryption Profiles: Bluetooth serial port Power supply: +3.3VDC 50mA Working temperature: -20 ~ +75 Centigrade Dimension: 26.9mm x 13mm x 2.2 mm Application: Computer and peripheral devices GPS receiver Industrial control MCU projects
R90  Inc Tax
HM-10 Bluetooth module
Logic level conversion circuit; RF-BM-S01 low power consumption Bluetooth module; Default baud rate: 9600 8N1; Soc: CC2540; 2.4GHz ISM band; GFSK; 40 channels, 2 MHz, 3 fixed broadcast channels, 37 adaptive auto frequency hopping data channels; Physical layer Bluetooth RF dual mode device; Output power adjustment (-23dBm~4dBm); High gain receiving sensitivity.

Bridge / direct-driven mode: after the Module is started, APP smart phone will scan and pair it, automatically enters transparent serial mode after device is paired and connected.

Widely used in instrument and meter, logical tracing, health and medical treatment, smart home, sports measurement, car electronic and toy, etc.

Main features: Easy to use; UART design; Support bridge direct-driven mode simultaneously (no need for extra CPU); 20ms connection interval (default), quick to connect; Support AT instruction, to modify the baud rate of the serial port, gain MAC address and modify module name; Support AT instruction, to adjust the Bluetooth connection interval and control the forwarding rate (dynamic power consumption adjustment); Support APP; IO expansion; 2 channel ADC input (14 bit); 4 channel PWM (120Hz) output; RSSI successive acquisition, auto read and notification to APP (used in anti-lost alarm); Power indicator / alert; Support anti-hajack password setup, modification and restoration; Ultra-low power consumption standby mode; Standby current: 0.4uA.

Quantity1 set
Working Voltage5V
Working Current3mA
Transmission Rate2.5K~2.8K
English Manual / SpecNo
Dimensions & Weight
Dimensions1.85 in x 0.67 in x 0.28 in (4.7 cm x 1.7 cm x 0.7 cm)
Weight0.18 oz (5 g)
Packing List
1 x Bluetooth module
R98  Inc Tax
NRF24 PCB antenne
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications.
125 Channels, Multi-point communication and frequency hopping to meet the communication needs
Built-in hardware CRC error detection, Multipoint communication address control.
Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
Built-in 2.4Ghz antenna
Available software to set the address, only received local Address when output data(Provide interrupt instruction), can be directly connected to a variety of microcontrollers, Software programming is very convenient.
Built-in voltage regulator
Standard DIP Pitch Interface for embedded applications
size: 34mm X 17mm X 1mm
R35  Inc Tax
Piezo speaker (27mm)
  • Uncased piezo elements
  • Speech and music applications
  • Wide tonal response
  • 12mm with flying leads
  • Resonant frequency(KHz)       Fs=9.0±1.0
    Resonant impedance(Ω)      Rr≤500Ω
    Capacitance at 120Hz(NF)    Co=11±30%
    Operating Temperature(℃) -20∽+70
    Storage Temperature(℃)     -30∽+80
  • Color: As the pictures shown
  • Material: Copper,PVC
R14  Inc Tax
Universal Infrared Receiver VS1838 TL1838 VS1838B

Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes.

The TL1838 is a miniaturized receiver for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame while the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TL1838 is compatible with all common IR remote control data formats.

R12  Inc Tax
UNO+WiFi R3 ATmega328P+ESP8266 32Mb (Shield W5100 )
Full integration on one board: Uno R3 ATmega 328 and WiFi ESP8266 with memory 32Mb (MegaByte). All of the modules can work together or each separately. And everyone has their own pinout headers.
The convenient solution for the development of new projects requiring Uno and WiFi.
Via USB you can update sketches and firmvare for ATmega328 and for ESP8266. For this on board have the USB-serial converter CH340G.
Use this board is very simple.
The board has DIP-switch, to connect the modules.
Driver link:
For example, to: USB and ATmega328, USB and ESP8266, ATmega328 and ESP8266.

Table DIP- switch:

USB<->ESP8266 (Update firmware or sketch)OFFOFFOFFOFFONONON

Package included:

1 x UNO+WiFi R3 ATmega328P+ESP8266 32Mb Memory
R201  Inc Tax
Per Page      1 - 13 of 13
  • 1