Sort By:  
R6  Inc Tax
R460  Inc Tax
R15  Inc Tax
R288  Inc Tax
FT232RL 3.3V 5.5V FTDI USB to TTL Serial Adapter Module for Arduino Mini Port

This programmer is used to flash code onto a Arduino Pro Mini 3.3V/5V

    100% brand new
    Support 3.3V, 5V
    chipset FT232RL
    USB power has over current protection, using 500MA self-restore fuse
    RXD/TXD transceiver communication indicator
    Pin definition: DTR,RXD,TX,VCC,CTS,GND
    Module size:36mm(length)*17.5mm(width)
    Driver download address:
R69  Inc Tax
3D Printer Parts Board High Power Expansion Add-on Heated Bed MOSFET Module

1. A plug-in power heating layer module for 3D printer
2. Can be used for the motherboard and other 3D printers available
3. The 3D printer equipped with the card controller
4. With this module, the maximum current is up to 25A

Maximum current25A
Package Included1 x Power module
1 x Cable
R186  Inc Tax
5V Regulator L7805
R6  Inc Tax
Aluminium Heat Sink 100X41X8mm
100x41x8mm Aluminum Heat Sink
R57  Inc Tax
Aluminium Heat Sink 40X40X10mm
40 x 40 x 11mm Aluminium Heat sink
R18  Inc Tax
Aluminium Heat Sink 40X40X20mm
40x40x20mm Aluminum Heat Sink
R48  Inc Tax
Aluminium Heat Sink 750x100x25mm
750x100x25mm Aluminum Heat Sink
R449  Inc Tax
Buck Booster 1500 W
  • DC / DC boost 1500Watt
R460  Inc Tax
Buck booster USB
  • DC / DC boost controller chip on board ultra-compact PFM control
  • Enter any DC voltage of 0.9V ~ 5V, can be stable output 5V DC voltage, output current of 500 ~ 600MA with two AA batteries input to a single AA battery-powered output current 200ma so, for the mobile phone, camera , single-chip, digital products supply. Stable output 5V DC voltage
  • Onboard USB female, can be directly powered USB interface device with USB female versatile
  • On-board input voltage indicator
  • PCB size: 34 (mm) x16.2 (mm) ultra-small size, installed in a variety of small equipment
R15  Inc Tax
DC Motor speed controller - 919D2PR Bi-Directional, 6-15V, 3A / 5A

919D Series Bi-Directional Speed Controller

Forward and reverse PWM speed regulator
Easy installation - unit panel mounted through 9.5mm hole. (Electrical connection via screw terminals)
6 → 15V operation d.c. (from smooth non digital d.c. input)
Output 0 → 100% of input voltage
Compact construction - board size 66 x 58mm

R497  Inc Tax
DC-DC Adjustable Step up / Step down Power Converter Module XL6009 ( XL6009)
DSN6009 4A is a high-performance step-up switching current (BOOST) module used to step up a lower supply voltage to a higher output voltage. The module uses the second generation of high-frequency switching technology XL6009E1 core chip performance than the first generation technology LM2577. XL6009 boost module at a lower cost, superior performance, LM2577 module is about to be eliminated.

● Wide input voltage 3V ~ 32V, optimum operating voltage range is 5 ~ 32V;
● Wide Output voltage 5V ~ 35V;
● Built-4A efficient MOSFET switches enable efficiency up to 94%; (LM2577 current is 3A)
● high switching frequency 400KHz, can use a small-capacity filter capacitors that can achieve very good results, the ripple smaller and smaller. (LM2577 frequency only 50KHz)

Technical parameters:
DSN6009 boost module

Module Properties
Non-isolated boost (BOOST)
Non-Synchronous Rectification
Input Range
3V ~ 32V
Output Range
5V ~ 35V
Input Current
4A (max), no-load 18mA (5V input, 8V output, no-load is less than 18mA. Higher the voltage, the greater the load current.)
Conversion efficiency
<94% (greater the pressure, the lower the efficiency)
Switching frequency
Output Ripple
50mV (the higher the voltage, the greater the current, the greater the ripple)
Load Regulation
± 0.5%
Voltage Regulation
± 0.5%
Operating Temperature
-40 ℃ ~ +85 ℃
43mm * 21mm * 14mm (L * W * H)
R54  Inc Tax
H-Bridge Dual Stepper Motor Controller
Onboard two the L9110S motor control chip
simultaneously drive two DC motors or a 4-wire 2-phase stepper motor
input voltage :2.5-12V
800mA continuous current output capability per channel

1. Low static work current

2. Power supply voltage: DC2.5-12V

3. Each channel has 800mA continuous current output

4. Low saturation pressure drop

5. TTL/CMOS output level compatible, can be connected directly to the CPU

6. Output built-in clamping diode, apply to the perceptual load

7. Control and drive integrate in IC

8. Pin high pressure protection function

9. Working temperature: 0-80 ℃
R31  Inc Tax
H-Bridge Stepper Motor Controller L298N for Arduino
The L298 is an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the con

1. Low static work current

2. Power supply voltage: DC5-36V

3. Each channel has 2500mA continuous current output

4. Low saturation pressure drop

5. TTL/CMOS output level compatible, can be connected directly to the CPU

6. Output built-in clamping diode, apply to the perceptual load

7. Control and drive integrate in IC
R52  Inc Tax
L293D 4 Channel Motor Driver
Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO Description:L293D is a monolithic integrated, high voltage, high current, 4-channel driver.
L293D is a monolithic integrated, high voltage, high current, 4-channel driver,you can use DC motors and power supplies of up to 36 Volts, the L293D chip is also known as a type of H-Bridge,which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.
  •     2 interface for 5V Servo connected to the Arduino’s high-resolution dedicated timer – no jitter.
  •     Can drive 4 DC motors or 2 stepper motors or 2 Servo.
  •     Up to 4 bi-directional DC motors with individual 8-bit speed selection.
  •     Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
  •     4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC.
  •     Pull down resistors keep motors disabled during power-up.
  •     2 external terminal power interface, for seperate logic/motor supplies.
  •     Tested compatible for Arduino Mega, Diecimila & Duemilanove.
  •     Reset button.
  • Control up to 4 DC motors.
  • Control 2 Servos.
  • Logic Control Voltage VSS: 4.5 ~ 5.5 V
  • Motor Supply Voltage VSS: 15v
  • Drive operating current IO: 1.2A
  • 8 Stage Serial Shift Registers

R69  Inc Tax
L298P Dual Channel Motor Driver & acc board

The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features.

Operating Voltage 5V to 12V
Motor controller   L298P, Drives 2 DC motors or 1 stepper motor
Max current  2A per channel or 4A max (with external power supply)
Current sensing    1.65V/A
Free running stop and brake function
R115  Inc Tax
LM338T LM338 Voltage Regulator 1.2V To 32V 1.5A TO-220 NS (1.2V To 32V )

This is the LM338T voltage regulator, a three-terminal positive regulator with a 1.2V to 37V adjustable output voltage. This adjustable regulator provides a local regulation, internal current limiting, thermal shut-down control, and safe area protection for your project. Did we mention that this guy is easy to use? It only requires two external resistors to set the output voltage. Each one of these voltage regulators can output a max current of 1.5A.


  • Output Voltage: 1.2V - 37V Adjustable
  • Output Current: 1.5A
  • Floating Operation for High Voltage Applications
R23  Inc Tax
LM4863 Audio Amplifier Sterio (2-5V)

Audio amplifier

Contact for more details

R17  Inc Tax
MINI USB 5V 1A 18650 TP4056 Lithium Battery Charger Module Charging Board


  • Board size: approx. 26 * 17mm

  • Input voltage: 5V

  • Charging cut-off voltage: 4.2V ± 1%

  • Maximum charge current: 1000mA

  • Battery over discharge protection voltage: 2.5V

  • Battery overcurrent protection current: 3A

R18  Inc Tax
MPPT Solar Panel Regulator Controller Battery Charging 9V 12V 24V Auto Switch 5A ( mppt)
Is suitable for stepping down solar panels to 9V 12V 24V batteries 
Input and output terminals are made of high-end switching power supply for high-frequency low-impedance electrolytic capacitors (LOW ESR), ensure that the output ripple. Can effectively filter out the switching power supply glitches.
Module parameters :
The modular nature: a real MPPT solar maximum power point tracking, automatic intelligent charge management, low power consumption
Input voltage: DC 8-28V input DC voltage. (Prohibition AC input)
Output voltage: DC 5-26V stepless transmission For lower output voltage, please contact the owner.
Charge indicator: Yes. Full automatic stop.
Low pressure: 1V (as is the step-down voltage regulator, the input voltage is at least higher than the output 1V)
Operating temperature: Industrial grade (-40 C to + 85 C)
Load regulation: ± 1%
Voltage regulation: ± 0.5%
Conversion efficiency: Max: 93% Peak: 95% for different lighting conditions vary.
Charging: automatic intelligent three-stage charging mode. Self-tracking solar power charge current automatically adjust the size
No-load current: 3MA even weak morning sunlight can easily start automatically, eliminating manual switch.
Note: The first charge in advance regulate the output voltage and please closely monitor the battery voltage to prevent overcharging! Do not charge unprotected lithium batteries.
Debugging method:
Step 1: Connect the solar cell, do not take the bottle to be charged, if the output voltage in step 2. If there is no transfer of small output counterclockwise slowly until the output voltage on the MPPT is high enough to engage the regulator.
Step 2: counterclockwise rotation of the pot will increase the output voltage until the indicator light red and the blue light flashes.
Step 3: Connect battery, and attach an ammeter to monitor the charging current, turn the MPPT trimming potentiometer until the charging current is at maximum.
Step 4: To adjust the output voltage maximum, connect a fully charged battery, if the blue light is on turn the Pot clockwise to up the output voltage until the red light turns on. Then turn the output voltage  down slowly (counterclockwise) until just blue light just turns on, and then use a multimeter to measure to determine the cut-off voltage is correct to avoid overcharging.
ransfer methods instead of using the power supply of solar energy:
Step 1: The power supply was adjusted Solar MPPT voltage (such as 18V)
Step 2: The power supply connected to the input terminal, do not take the battery to be charged, if the output voltage is adjusted clockwise until no large MPPT voltage output. Then slowly counterclockwise until the transfer of small MPPT just have the output voltage.
Step 3: anti-clockwise turn down the output voltage until the red and blue lights flashing, then coarse output voltage to a full cut-off voltage
Step 4: Access is just full of batteries, if the blue light is clockwise turn up the output voltage until the red light. Then transfer a small output voltage slowly counterclockwise until just blue lights, and then use a multimeter to measure to determine the cut-off voltage is correct to avoid overcharge!
Package include:
1 x 5A MPPT Solar Panel Regulator Controller Battery Charging 9V 12V 24V Auto Switch
R173  Inc Tax
NE555 Pulse Module LM358 Duty and Frequency Adjustable Square
1. Size: 3.5CM * 4.6CM
1. The main chip: LM358;
2. Input voltage: 5V-12VDC.
3. Input current: ≥100MA;
4. The output amplitude: close to the input voltage;
5. The frequency adjustment range: 0.07HZ-2KHZ (that is, the cycle is about 0.45 milliseconds to 15 seconds)
6. Duty cycle adjustment range: 0% to 100% (high level / period);
7. Output current: plate with 9012 triode, so the driving ability is relatively strong, the output current can be up to 500MA, the output can directly drive small relay or small motor;
R26  Inc Tax
PWM Servo Sheild -B
Looking to build an Arduino based robot? Drive a ton of LEDs with a very precise PWM output? The Arduino Uno only has a limited number of PWM pins – this shield adds an additional 16 PWM channels, each with 12 Bit resolution! Since this board communicates using I2C, up to 62 of these boards can be used on the same Arduino. That means you can control up to 992 PWM outputs!
  • Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs
  • It's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
  • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
  • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
  • Adjustable frequency PWM up to about 1.6 KHz
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
  • Configurable push-pull or open-drain output
  • Output enable pin to quickly disable all the outputs
  • Terminal block for power input (or you can use the 0.1" breakouts on the side)
  • Reverse polarity protection on the terminal block input
  • Green power-good LED
  • 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
  • "Chain-able" design
  • A spot to place a big capacitor on the V+ line (in case you need it)
  • 330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
  • Solder jumpers for the 6 address select pins
R288  Inc Tax
Stelltron Breakout board
  • Fits 22 pin Dip packages 
  • Supports SMD components
  • Ideal for prototypes that need to last longer
  • Through hole connections make it ideal for osilator and filter projects
  • Dimentions 61x50mm
  • Bottom pads next to Dip area are used for decoupling (Any connection to ground as in caps/resistors)
R35  Inc Tax
TIP122 NPN Transistor Complementary 100V 5A (Tip122)
Ideal for use with a microcontroller to drive high current loads.
  • Manufacturer Part No TIP122
  • RoHS Compliance Yes
  • Package / Case TO-220
  • Current Rating 5A
  • Voltage Rated 100V
  • Transistor Type NPN
  • Features Darlington Transistors
R6  Inc Tax
Universal Infrared Receiver VS1838 TL1838 VS1838B

Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes.

The TL1838 is a miniaturized receiver for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame while the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TL1838 is compatible with all common IR remote control data formats.

R12  Inc Tax
Zartek Rechargeable Li-ion Battery 18650 3.7V (18650 )
Rechargeable lithium ion battery 1200mAh
R168  Inc Tax
Per Page      1 - 27 of 27
  • 1