Voltage Regulators

Sort By:  
R6  Inc Tax
R460  Inc Tax
R15  Inc Tax
3D Printer Parts Board High Power Expansion Add-on Heated Bed MOSFET Module
Features:

1. A plug-in power heating layer module for 3D printer
2. Can be used for the motherboard and other 3D printers available
3. The 3D printer equipped with the card controller
4. With this module, the maximum current is up to 25A


Specifications
ColorBlack
Maximum current25A
Size55x45x28mm
Weight36g
Package Included1 x Power module
1 x Cable
R186  Inc Tax
5V Regulator L7805
1.5A
+5V
R6  Inc Tax
Buck Booster 1500 W
  • DC / DC boost 1500Watt
R460  Inc Tax
Buck booster USB
  • DC / DC boost controller chip on board ultra-compact PFM control
  • Enter any DC voltage of 0.9V ~ 5V, can be stable output 5V DC voltage, output current of 500 ~ 600MA with two AA batteries input to a single AA battery-powered output current 200ma so, for the mobile phone, camera , single-chip, digital products supply. Stable output 5V DC voltage
  • Onboard USB female, can be directly powered USB interface device with USB female versatile
  • On-board input voltage indicator
  • PCB size: 34 (mm) x16.2 (mm) ultra-small size, installed in a variety of small equipment
R15  Inc Tax
DC-DC Adjustable Step up / Step down Power Converter Module XL6009 ( XL6009)
DSN6009 4A is a high-performance step-up switching current (BOOST) module used to step up a lower supply voltage to a higher output voltage. The module uses the second generation of high-frequency switching technology XL6009E1 core chip performance than the first generation technology LM2577. XL6009 boost module at a lower cost, superior performance, LM2577 module is about to be eliminated.

● Wide input voltage 3V ~ 32V, optimum operating voltage range is 5 ~ 32V;
● Wide Output voltage 5V ~ 35V;
● Built-4A efficient MOSFET switches enable efficiency up to 94%; (LM2577 current is 3A)
● high switching frequency 400KHz, can use a small-capacity filter capacitors that can achieve very good results, the ripple smaller and smaller. (LM2577 frequency only 50KHz)



Technical parameters:
DSN6009 boost module

Module Properties
Non-isolated boost (BOOST)
Rectification
Non-Synchronous Rectification
Input Range
3V ~ 32V
Output Range
5V ~ 35V
Input Current
4A (max), no-load 18mA (5V input, 8V output, no-load is less than 18mA. Higher the voltage, the greater the load current.)
Conversion efficiency
<94% (greater the pressure, the lower the efficiency)
Switching frequency
400KHz
Output Ripple
50mV (the higher the voltage, the greater the current, the greater the ripple)
Load Regulation
± 0.5%
Voltage Regulation
± 0.5%
Operating Temperature
-40 ℃ ~ +85 ℃
Dimensions
43mm * 21mm * 14mm (L * W * H)
R54  Inc Tax
LAM Technologies Programmable Stepper Motor driver DS30 Series DS3044 (50Vdc 4Arms 5.6Apk) (DS3044)
This is a high quality stepper motor driver unit from LAM Technologies.

These rugged units are DIN Rail mountable. 

See series Broucher link: 
https://drive.google.com/open?id=1j9_EtHJR1baWrxCmBTUk2R3RNR1pk45D

If you require a datasheet please email Peter at peter@hornet.cc
R3,256  Inc Tax
LAM Technologies Stepper Motor driver DS10 Series DS1078 (90Vdc 10Arms 14.1Apk) (1078)
This is a high quality stepper motor driver unit from LAM Technologies.

These rugged units are DIN Rail mountable. 

See series Broucher link: 
https://drive.google.com/open?id=1j9_EtHJR1baWrxCmBTUk2R3RNR1pk45D

If you require a datasheet please email Peter at peter@hornet.cc
R3,725  Inc Tax
LM338T LM338 Voltage Regulator 1.2V To 32V 1.5A TO-220 NS (1.2V To 32V )

This is the LM338T voltage regulator, a three-terminal positive regulator with a 1.2V to 37V adjustable output voltage. This adjustable regulator provides a local regulation, internal current limiting, thermal shut-down control, and safe area protection for your project. Did we mention that this guy is easy to use? It only requires two external resistors to set the output voltage. Each one of these voltage regulators can output a max current of 1.5A.

Features:

  • Output Voltage: 1.2V - 37V Adjustable
  • Output Current: 1.5A
  • Floating Operation for High Voltage Applications
R23  Inc Tax
Microstepping drives DS1041 (50Vdc 1.4Arms 2Apk)
Maximum reliability, high performance, small footprint and low cost are the guidelines followed in the design of the stepper motor drives belonging to the xS10 series .

The company's know-how, gained in over 20 years of experience, has allowed to create a range of drives characterized by compact size, low cost and innovative features.

All the models can drive the stepper motor in bipolar mode, with a resolution up to 1/128 steps, both decimal and binary.
4-6 Weeks Lead Time
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R2,820  Inc Tax
Microstepping drives DS1044 (50Vdc 4Arms 5.6Apk)
Maximum reliability, high performance, small footprint and low cost are the guidelines followed in the design of the stepper motor drives belonging to the xS10 series .

The company's know-how, gained in over 20 years of experience, has allowed to create a range of drives characterized by compact size, low cost and innovative features.

All the models can drive the stepper motor in bipolar mode, with a resolution up to 1/128 steps, both decimal and binary.
4-6 Weeks Lead Time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R3,223  Inc Tax
Microstepping drives DS1048 (50Vdc 8Arms 11.3Apk)
Maximum reliability, high performance, small footprint and low cost are the guidelines followed in the design of the stepper motor drives belonging to the xS10 series .

The company's know-how, gained in over 20 years of experience, has allowed to create a range of drives characterized by compact size, low cost and innovative features.

All the models can drive the stepper motor in bipolar mode, with a resolution up to 1/128 steps, both decimal and binary.
4-6 Weeks Lead Time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R4,378  Inc Tax
Microstepping drives DS1078 (90Vdc 10Arms 14.1Apk)
Maximum reliability, high performance, small footprint and low cost are the guidelines followed in the design of the stepper motor drives belonging to the xS10 series .

The company's know-how, gained in over 20 years of experience, has allowed to create a range of drives characterized by compact size, low cost and innovative features.

All the models can drive the stepper motor in bipolar mode, with a resolution up to 1/128 steps, both decimal and binary.
4-6 Weeks Lead Time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R5,479  Inc Tax
MINI USB 5V 1A 18650 TP4056 Lithium Battery Charger Module Charging Board

Specification:

  • Board size: approx. 26 * 17mm

  • Input voltage: 5V

  • Charging cut-off voltage: 4.2V ± 1%

  • Maximum charge current: 1000mA

  • Battery over discharge protection voltage: 2.5V

  • Battery overcurrent protection current: 3A

R18  Inc Tax
MPPT Solar Panel Regulator Controller Battery Charging 9V 12V 24V Auto Switch 5A ( mppt)
Is suitable for stepping down solar panels to 9V 12V 24V batteries 
 
Input and output terminals are made of high-end switching power supply for high-frequency low-impedance electrolytic capacitors (LOW ESR), ensure that the output ripple. Can effectively filter out the switching power supply glitches.
 
Module parameters :
 
The modular nature: a real MPPT solar maximum power point tracking, automatic intelligent charge management, low power consumption
 
Input voltage: DC 8-28V input DC voltage. (Prohibition AC input)
 
Output voltage: DC 5-26V stepless transmission For lower output voltage, please contact the owner.
 
 
Charge indicator: Yes. Full automatic stop.
 
Low pressure: 1V (as is the step-down voltage regulator, the input voltage is at least higher than the output 1V)
 
Operating temperature: Industrial grade (-40 C to + 85 C)
 
Load regulation: ± 1%
 
Voltage regulation: ± 0.5%
 
Conversion efficiency: Max: 93% Peak: 95% for different lighting conditions vary.
 
Charging: automatic intelligent three-stage charging mode. Self-tracking solar power charge current automatically adjust the size
 
 
No-load current: 3MA even weak morning sunlight can easily start automatically, eliminating manual switch.
  
Note: The first charge in advance regulate the output voltage and please closely monitor the battery voltage to prevent overcharging! Do not charge unprotected lithium batteries.
 
Debugging method:
 
Step 1: Connect the solar cell, do not take the bottle to be charged, if the output voltage in step 2. If there is no transfer of small output counterclockwise slowly until the output voltage on the MPPT is high enough to engage the regulator.
 
Step 2: counterclockwise rotation of the pot will increase the output voltage until the indicator light red and the blue light flashes.
 
Step 3: Connect battery, and attach an ammeter to monitor the charging current, turn the MPPT trimming potentiometer until the charging current is at maximum.
 
Step 4: To adjust the output voltage maximum, connect a fully charged battery, if the blue light is on turn the Pot clockwise to up the output voltage until the red light turns on. Then turn the output voltage  down slowly (counterclockwise) until just blue light just turns on, and then use a multimeter to measure to determine the cut-off voltage is correct to avoid overcharging.
 
ransfer methods instead of using the power supply of solar energy:
 
Step 1: The power supply was adjusted Solar MPPT voltage (such as 18V)
 
Step 2: The power supply connected to the input terminal, do not take the battery to be charged, if the output voltage is adjusted clockwise until no large MPPT voltage output. Then slowly counterclockwise until the transfer of small MPPT just have the output voltage.
 
Step 3: anti-clockwise turn down the output voltage until the red and blue lights flashing, then coarse output voltage to a full cut-off voltage
 
Step 4: Access is just full of batteries, if the blue light is clockwise turn up the output voltage until the red light. Then transfer a small output voltage slowly counterclockwise until just blue lights, and then use a multimeter to measure to determine the cut-off voltage is correct to avoid overcharge!
 
  
Package include:
 
1 x 5A MPPT Solar Panel Regulator Controller Battery Charging 9V 12V 24V Auto Switch
R173  Inc Tax
Nema 17 M1173020 (0.28Nm 0.7A)
A wide range of stepper motors available from stock characterized by high torque, compact size and competitive price.LAM Technologies offers high quality stepper motors in combination with its drives to provide a modern and performing motion control solution. 4 week lead time     https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE
R868  Inc Tax
Nema 17 M1173030 (0.40Nm 0.7A)

https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE
The motors with torque higher than 1,5Nm (213 oz-in) are available with shaft with single or double flat, for a simple and secure fastening. Upon request, we can provide stepper motors with key and double shaft. 4-6 weeks Lead time.
R904  Inc Tax
Nema 17 M1173040 (0.50Nm 0.7A)
The motors with torque higher than 1,5Nm (213 oz-in) are available with shaft with single or double flat, for a simple and secure fastening. Upon request, we can provide stepper motors with key and double shaft. 4-6 Weeks lead time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE
R957  Inc Tax
Nema 23 M1233070S8 (3.0Nm 4.2A)

The motor shaft can be supplied with a diameter of 6,35mm (0,250In) or 8mm (0,315In) with flattening (recommended for motors with torque over 1,5Nm 213In).

The models M1233070 and M1233071 supply the highest torque amongst the motors with NEMA23 flange available on the market.
4-6 Weeks Lead Time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R2,070  Inc Tax
Nema 23 M1233021 (0.80Nm 0.62A)
The motor shaft can be supplied with a diameter of 6,35mm (0,250In) or 8mm (0,315In) with flattening (recommended for motors with torque over 1,5Nm 213In).
4-6 Week Lead Time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE
R1,083  Inc Tax
Nema 34 M1343020 (4.4Nm 5.6A)

The maximum torque exceeds 12Nm (1416oz-In) placing this series of stepper motors among the best performing commercially available.

All the motors have 8 wires and can be used both in bipolar and unipolar mode.

When the motors are used in bipolar mode (recommended to obtain the best performance) it is possible to choose between a series type connection, to limit the phase current, or parallel type, for applications exploiting the motors at high speeds.

The 14mm shaft diameter ensures stability in applications with belt transmission. Upon request the motor can be realized with 12mm shaft with key, with double shaft, etc.
4-6 Weeks Lead Time
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R3,473  Inc Tax
Nema 34 M1343050 (9.2Nm 7.1A)

The maximum torque exceeds 12Nm (1416oz-In) placing this series of stepper motors among the best performing commercially available.

All the motors have 8 wires and can be used both in bipolar and unipolar mode.

When the motors are used in bipolar mode (recommended to obtain the best performance) it is possible to choose between a series type connection, to limit the phase current, or parallel type, for applications exploiting the motors at high speeds.

The 14mm shaft diameter ensures stability in applications with belt transmission. Upon request the motor can be realized with 12mm shaft with key, with double shaft, etc.
4-6 Weeks Lead Time
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R4,876  Inc Tax
Nema 34 M1343060 (12.1Nm 10.0A)

The maximum torque exceeds 12Nm (1416oz-In) placing this series of stepper motors among the best performing commercially available.

All the motors have 8 wires and can be used both in bipolar and unipolar mode.

When the motors are used in bipolar mode (recommended to obtain the best performance) it is possible to choose between a series type connection, to limit the phase current, or parallel type, for applications exploiting the motors at high speeds.

The 14mm shaft diameter ensures stability in applications with belt transmission. Upon request the motor can be realized with 12mm shaft with key, with double shaft, etc.
4-6 Weeks Lead Time
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R5,648  Inc Tax
Nema 42 M1433010 (14.4Nm 10.0A)
With a static torque up to 29Nm (4107oz-In) the NEMA42 stepper motors are used successfully in the most demanding applications.

Supplied with 19mm diameter shaft and key, they can be mechanically and electrically customized.

The windings have 8 wires and can therefore be used with unipolar type drives. When used in bipolar mode (recommended) it is possible to choose between a series type connection, to limit the phase current, or a parallel type, for applications exploiting the motors at high speeds.
4-6 Weeks Lead Time
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R8,444  Inc Tax
Nema 42 M1433040 (28.0Nm 10.0A)
With a static torque up to 29Nm (4107oz-In) the NEMA42 stepper motors are used successfully in the most demanding applications.

Supplied with 19mm diameter shaft and key, they can be mechanically and electrically customized.

The windings have 8 wires and can therefore be used with unipolar type drives. When used in bipolar mode (recommended) it is possible to choose between a series type connection, to limit the phase current, or a parallel type, for applications exploiting the motors at high speeds.
4-6 Weeks Lead Time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R16,435  Inc Tax
Nema23 M1233032D (1.1Nm 2.5A)
The motor shaft can be supplied with a diameter of 6,35mm (0,250In) or 8mm (0,315In) with flattening (recommended for motors with torque over 1,5Nm 213In).
4-6 Weeks Lead Time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE
R1,011
Nema23 M1233061 (1.8Nm 3.0A)

The motor shaft can be supplied with a diameter of 6,35mm (0,250In) or 8mm (0,315In) with flattening (recommended for motors with torque over 1,5Nm 213In).

The models M1233070 and M1233071 supply the highest torque amongst the motors with NEMA23 flange available on the market.

4-6 Weeks Lead Time.
https://drive.google.com/drive/folders/0BySRlxy9ZcVccko2MGM3U0lldlE

R1,553  Inc Tax
Zartek Rechargeable Li-ion Battery 18650 3.7V (18650 )
Rechargeable lithium ion battery 1200mAh
R168  Inc Tax
Per Page      1 - 29 of 29
  • 1